Trading – Agriculture / INSIGHTS

Sugar Buying Specification: Colour Method, Grain Size and Packing

Published · 5 min read

A sugar buying specification must define how quality is measured, not only state a familiar grade name. A colour limit without an analytical method, a grain-size request without a sieve basis, or a packing line without material and closure details can produce offers that appear comparable but describe different products.

Procurement teams should convert the intended application into measurable limits, agreed test methods and a complete packing requirement before requesting a firm offer.

Build the Sugar Buying Specification Around the Application

Start with the intended use: retail packing, industrial food production, beverages, confectionery, bakery, institutional supply or further refining. The application affects which parameters are commercially important and how tight the limits should be.

Identify:

  • sugar type, such as refined white, plantation white, raw or brown;
  • intended use and any processing sensitivity;
  • origin requirement, if commercially necessary;
  • required quantity and delivery period;
  • inspection and sampling arrangement;
  • test methods and certificate requirements;
  • packing format, marking and palletisation;
  • destination regulations to be confirmed by the importer.

Avoid treating a trade description as a complete technical specification. Two suppliers may use the same general grade name while offering different colour, moisture, crystal distribution or packing.

State the Colour Method and Limit

Colour in solution is not the same as the visual appearance of dry crystals. The specification should state the parameter, numerical limit, unit, analytical method and applicable product range.

ICUMSA maintains recognised sugar analysis methods. Current examples include GS2-10 for colour in solution of very low-colour white sugars and syrups, and GS2-9 for a broader range of crystalline and powdered sugars. The methods differ in scope and sample preparation. The contract should name the method and edition agreed for the product rather than use “ICUMSA” as if it were a single test.

Confirm:

  • whether the requirement is colour in solution or visual appearance;
  • maximum ICUMSA Units, where applicable;
  • named method and edition;
  • pH adjustment or buffer basis used by that method;
  • sample preparation and laboratory responsibility;
  • treatment of results near the contractual limit;
  • referee laboratory or dispute procedure.

Do not compare results produced by different methods without technical review. Method selection can affect whether two certificates are genuinely comparable.

Define Grain Size as a Distribution

“Fine,” “medium” and “large crystal” are descriptive terms unless the parties attach measurable limits. Grain size can affect dissolving rate, dust, flow, blending, dosing and the appearance of retail product.

Specify the required reporting format, such as:

  • percentage retained on named sieve apertures;
  • percentage passing a named sieve;
  • mean aperture or mean particle size;
  • coefficient of variation or another agreed uniformity measure;
  • maximum fine fraction;
  • maximum oversized fraction.

ICUMSA lists sieving methods for particle-size distribution of raw and white sugars. Use the method appropriate to the sugar type and agreed edition. State sieve apertures in a recognised unit and avoid mixing mesh numbers from different sieve systems without conversion.

Align sampling with the contract

A laboratory result is only as representative as the sample. Define whether sampling occurs during production, at packing, from the warehouse lot, at loading or at destination. Record the lot size, number of increments, composite-sample process, sealing and retention period.

If the buyer requires pre-shipment inspection, state who appoints and pays the inspector, what the inspector witnesses, how samples are sealed and what happens if results are outside specification.

Complete the Quality Schedule

Colour and grain size do not replace the other required parameters. Depending on product and application, the schedule may address:

  • polarimetric sucrose content;
  • moisture or loss on drying;
  • conductivity ash;
  • reducing sugars;
  • insoluble matter;
  • sulphur dioxide where relevant;
  • microbiological criteria for the intended use;
  • foreign matter and sensory condition;
  • any destination-specific food-safety or labelling requirement.

Use only limits supported by the application, regulation and supply agreement. The buyer should verify the legal requirements of the importing market; a supplier’s typical certificate is not proof that every destination requirement is covered.

Specify Packing as a Technical Requirement

State the net content and permissible tolerance, bag or container construction, liner requirement, closure method and marking. “50 kg bags” alone leaves important decisions open.

Confirm:

  • bag material and ply or fabric construction;
  • food-contact liner, if required;
  • liner and outer-bag closure method;
  • nominal net weight and permitted variation;
  • printing language and mandatory marks;
  • lot, production or packing-date coding;
  • pallet type, pattern and maximum height;
  • stretch wrap, straps, corner protection or slip sheets;
  • container loading method and moisture protection;
  • whether pallets must comply with destination wood-packaging rules.

For container shipments, agree whether bags are floor-loaded or palletised and how quantity is reconciled. Confirm container cleanliness, dryness, odour condition and protection from condensation. Desiccants or liners should be selected through a documented risk assessment, not inserted as an assumed cure for every route.

Make Supplier Offers Comparable

Issue the same request schedule to each supplier and require deviations to be listed line by line. Compare the offer, specification sheet, certificate of analysis, packing declaration and inspection proposal together.

Before contracting, close these points:

  1. exact product and origin description;
  2. each limit and named test method;
  3. sampling and inspection point;
  4. packing and marking specification;
  5. quantity tolerance;
  6. document set;
  7. treatment of non-conforming results;
  8. Incoterm, named place and delivery window.

Takeaway

A practical sugar buying specification links the application to a defined colour method, measurable grain-size distribution, representative sampling and complete packing details. This makes supplier offers comparable and gives inspection teams an objective acceptance basis.

Send your sugar requirement and specification to ZSCM Trading at sales@zscm.global.

References

More insights

SOURCING / SHARE YOUR REQUIREMENTS

Source your
next order.

Share the product, specification, quantity and destination so we can review your sourcing request.

Share product requirements
ZSCM
ZSCM TRADINGPRODUCTS / PROCUREMENT
Logistics division ↗Return to the opening ↗