Trading – Machinery / INSIGHTS

Mobile Crane Procurement: Load Chart, Radius and Ground Support

Published · 5 min read

Mobile crane procurement should begin with the heaviest planned lift at the actual working radius and configuration. A headline crane capacity is normally associated with a limited radius and setup, while boom length, counterweight, outriggers, reeving, wind and ground support can reduce usable capacity.

Procurement teams need a duty schedule and site data that allow suppliers to select and document a complete, workable crane configuration.

Define the Mobile Crane Procurement Duty

Issue a lift-duty schedule rather than requesting a crane only by nominal tonnage. Record:

  • maximum lifted load, including hook block, rigging and lifting accessories;
  • load dimensions and centre of gravity;
  • pick and set locations;
  • minimum and maximum working radius;
  • required hook height;
  • obstructions and available boom path;
  • number and frequency of lifts;
  • travel with load, if permitted and required;
  • site altitude, temperature and wind conditions;
  • ground bearing and setup area;
  • road, bridge and access constraints;
  • applicable local lifting regulations and operator requirements.

Treat the nominal capacity as a product-class label, not proof that the crane can perform the planned lift.

Check the Load Chart for the Exact Configuration

Require manufacturer load charts covering the offered crane, boom, jib, counterweight, outrigger position, tyre or crawler condition and operating sector.

For each critical lift, confirm:

  1. gross load imposed on the crane;
  2. working radius measured under the defined conditions;
  3. boom length and angle;
  4. main boom or jib configuration;
  5. counterweight installed;
  6. outrigger extension or crawler setup;
  7. parts of line and hook block;
  8. capacity for the operating sector;
  9. deductions required by the manufacturer;
  10. remaining margin under the adopted lift plan.

OSHA’s technical criteria for crane operators illustrate why configuration matters: load-chart use must relate boom length, load radius, crawler or outrigger position, jib offset and counterweight. OSHA rules apply to covered US construction work; buyers must confirm the law and standards for the intended country.

Verify Radius, Height and Access Together

A crane may reach the hook height but lack capacity at the necessary radius. Obtain a scaled site layout showing the setup point, tail-swing clearance, boom path, load path and landing area.

  • Measure radius from the crane’s reference point specified by the manufacturer.
  • Include clearance from buildings, power lines and temporary works.
  • Check whether outriggers can be fully deployed.
  • Confirm counterweight installation space and support equipment.
  • Allow access for the carrier, assembly vehicles and rigging team.
  • Identify underground services, basements and slab edges.

Define Ground Support Information

Ask the supplier for maximum outrigger or crawler reactions for the proposed configuration and load cases. The site owner or qualified engineer should assess whether the ground and supporting structure can carry them.

The procurement file should include:

  • ground investigation or verified bearing information;
  • surface slope and level tolerance;
  • drainage and weather exposure;
  • underground services and voids;
  • mat, cribbing or engineered spreader requirements;
  • maximum permissible ground pressure or structural load;
  • setup inspection and approval responsibility.

OSHA 1926.1402 requires covered equipment not to be assembled or used unless ground conditions are sufficiently firm, drained and graded, with supporting materials where necessary, to meet manufacturer support and level requirements. Use this as a jurisdiction-specific reference, not as a universal substitute for local rules.

Specify Crane Equipment and Operational Aids

Define the required equipment instead of assuming it is standard:

  • rated-capacity or load-moment system;
  • boom angle or radius indication;
  • anti-two-block protection;
  • wind-speed indication where required;
  • outrigger monitoring;
  • work-area limitation;
  • camera or visibility aids;
  • lighting and communication equipment;
  • hook blocks, headache ball and reeving components;
  • jib, inserts, auxiliary winch and counterweights;
  • fire suppression or site-specific safety equipment;
  • telematics and maintenance data access.

Confirm which aids are included, their limits, calibration or inspection arrangements and the permitted response to a malfunction under the governing rules.

Review Transport, Assembly and Documentation Scope

Large mobile cranes may require separate transport for counterweights, boom sections, mats and accessories. Clarify:

  • transport dimensions and axle loads;
  • number and type of support vehicles;
  • road permits and escort responsibility;
  • assembly crane requirements;
  • site assembly area;
  • commissioning and functional tests;
  • operator and maintenance training;
  • spare parts and special tools;
  • warranty boundaries and service support;
  • language and format of manuals.

Plan Acceptance Around the Offered Duty

Factory documentation alone does not prove site suitability. Acceptance should verify the delivered configuration and agreed functions.

  1. Match serial numbers and configuration to the purchase order.
  2. Review certificates, manuals, load charts and maintenance records.
  3. Inspect structural, hydraulic, electrical and rope systems.
  4. Verify safety devices and operational aids.
  5. Check supplied counterweights, mats, hooks and accessories.
  6. Perform functional and load testing only under the approved procedure and applicable rules.
  7. Close defects and document final acceptance.

Do not improvise a test load or exceed the manufacturer’s procedure. Testing must be planned by competent personnel under the applicable standard and local law.

Mobile Crane Procurement Checklist

  • The critical lift duty includes radius and hook height.
  • Manufacturer charts match the exact offered configuration.
  • Gross load includes rigging and hook equipment.
  • Outrigger, counterweight and operating sector are defined.
  • Ground reactions and support responsibilities are documented.
  • Transport and assembly scope is priced.
  • Operational aids and accessories are listed.
  • Acceptance tests and documents are agreed.
  • Local regulatory and operator requirements are confirmed.

Takeaway

Mobile crane procurement is a configuration decision, not a nominal-capacity purchase. Load charts, site geometry, ground reactions, transport scope and acceptance evidence must be evaluated together against the planned lifts.

Send your lift duty, site layout and required configuration to ZSCM Trading at sales@zscm.global.

References

More insights

SOURCING / SHARE YOUR REQUIREMENTS

Source your
next order.

Share the product, specification, quantity and destination so we can review your sourcing request.

Share product requirements
ZSCM
ZSCM TRADINGPRODUCTS / PROCUREMENT
Logistics division ↗Return to the opening ↗