Buyers should define sieve construction, fraction limits, sample preparation and reporting before comparing prices.
Write the Chickpea Size Specification as a Distribution
State the chickpea type and intended application first. Kabuli, desi, whole food, canning, splitting and milling requirements may place different importance on appearance, uniformity and size.
The size schedule should identify:
- chickpea type and variety where required;
- round-hole sieve aperture or defined alternative;
- metric or inch unit;
- sieve stack and test sequence;
- percentage retained on each sieve;
- percentage passing the smallest agreed sieve;
- maximum oversized and undersized fractions;
- calculation basis, normally weight unless agreed otherwise;
- sample size and preparation;
- method, edition and laboratory.
Avoid describing the entire lot as a single nominal diameter. Agricultural products vary, so the acceptance decision should use agreed fractions.
Define What “On” and “Through” Mean
“On 22/64” means the chickpeas remaining on a round-hole sieve with openings of 22/64 inch under the referenced U.S. procedure. A fraction described as “on 20/64” may mean material passing the 22/64 sieve and remaining on the 20/64 sieve. These statements are not interchangeable with “minimum 20/64” unless the contract defines the calculation.
USDA Federal Grain Inspection Service guidance effective from 31 October 2024 reports chickpea size categories including:
- remaining on a 22/64-inch round-hole sieve;
- passing 22/64 and/or remaining on 20/64;
- passing 20/64 and remaining on 18/64;
- passing 18/64 and remaining on 16/64.
A further USDA certification update effective 13 April 2025 added factors including the fraction remaining on 24/64 and a metric fraction passing 7 mm and remaining on 6 mm. These are U.S. certification examples, not mandatory commercial categories for every origin or market.
Do not mix sieve systems casually
An inch fraction, a millimetre aperture and a commercial label such as “9 mm” must be tied to the actual sieve opening and procedure. A mathematical conversion alone does not confirm that two sieve plates, hole patterns or test methods produce identical classification.
Record:
- aperture dimension;
- round, slotted or other opening shape;
- sieve plate or mesh reference;
- agitation time and equipment;
- treatment of broken or split chickpeas;
- rounding rule for reported percentages.
Separate Sieve Fractions from Seed Count
Seed count reports the number of seeds in a stated weight, such as seeds per ounce or seeds per 100 grams. It can support a size description but does not replace the sieve distribution.
Count can be affected by density, shape, moisture and the fraction selected for counting. If seed count is required, state:
- weight unit;
- whether the count covers the whole sample or a named sieve fraction;
- number of replicate counts;
- treatment of splits and broken pieces;
- reporting and rounding rule.
Compare supplier offers only when the count basis matches. “40–42 count” is incomplete without the weight unit and sampling method.
Set Acceptable Fractions and Tolerances
A useful buying schedule shows the permitted distribution. For example, it may set a minimum percentage retained on the target sieve, a maximum percentage in the next smaller fraction and a maximum passing the smallest sieve. These figures are contractual examples and must be selected for the buyer’s application and supply market.
Do not specify an unrealistically narrow band without considering cleaning yield, seasonal crop variation and the intended process. Ask suppliers to list deviations rather than substitute their standard size statement.
Also confirm whether the size result is:
- guaranteed at loading;
- typical or indicative only;
- tested by the supplier’s laboratory;
- verified by an independent inspector;
- subject to a destination retest;
- averaged across sub-lots or reported for each lot.
Link Size to the Full Quality Specification
Size alone does not establish grade or suitability. The purchase specification should also address, as applicable:
- moisture;
- foreign material;
- damaged, discoloured or immature chickpeas;
- splits and broken seeds;
- contrasting chickpeas or other varieties;
- insect damage and live infestation;
- odour and visible mould;
- crop year and origin;
- food-safety and destination requirements;
- packing, net weight and lot marking.
USDA’s bean standards determine percentages by weight unless an individual factor requires another basis. Name the grading standard only when both parties intend to use its full definitions and procedures; selecting one sieve term does not automatically adopt the complete standard.
Control Sampling and Inspection
Define where the sample represents the lot: production line, warehouse lot, truck, container loading or destination. State the lot size, number of increments, composite method, sample division, sealing and retention period.
Before acceptance, reconcile:
- purchase contract and final specification;
- supplier certificate of analysis;
- inspection report;
- sieve result worksheet;
- retained-sample seal numbers;
- packing-list lot references;
- any approved concession.
If a result is close to a limit, apply the agreed method’s repeatability, rounding and dispute provisions rather than informally reclassifying the lot.
Takeaway
A defensible chickpea size specification states the actual sieve system, fraction definitions, percentage basis, seed-count basis and sampling method. This makes offers comparable and gives inspection teams an objective acceptance rule.
Send your chickpea requirement and quality specification to ZSCM Trading at sales@zscm.global.
